NSW CER Installer Portal: What solar and battery installers need to know
New installation and commissioning requirements are being introduced across NSW from November 2026. Here’s what they mean for your workflow.
The NSW Government has launched the new Consumer Energy Resources (CER) Installer Portal, changing how installers register and commission new and upgraded solar and battery systems across the state.
The portal brings together installation registration, network requirements and electrical certification into a single process, helping installers meet requirements across NSW’s three electricity distribution networks.
The changes are being introduced in stages, with Endeavour Energy installations transitioning from 2 November 2026, followed by Ausgrid and Essential Energy on 23 November 2026.
Key dates for installers
| Date | What’s changing |
|---|---|
| 2 November 2026 | NSW CER Installer Portal requirements commence for eligible new and upgraded Endeavour Energy installations. |
| 23 November 2026 | Requirements commence for eligible Ausgrid and Essential Energy installations. |
| November 2026 onwards | Emergency Backstop capability requirements are progressively introduced by network and location. |
| 1 February 2027 | Endeavour Energy’s transition to Emergency Backstop requirements reaches its network-wide milestone for new and upgraded solar systems. |
| 30 April 2027 | Endeavour Energy’s installation deadline for qualifying legacy connection approvals made before 1 February 2027. |
What’s changing?
The NSW CER Installer Portal introduces a new process for registering and commissioning eligible grid-connected solar PV and battery systems with inverter capacity up to and including 200 kW.
For applicable installations, the portal will:
- Capture installation and commissioning information.
- Support the Certificate of Compliance for Electrical Work (CCEW) submission process.
- Provide information required for AEMO’s Distributed Energy Resources Register (DERR).
- Support verification of compatible equipment and connectivity to electricity distribution networks.
- Enable the phased introduction of the NSW Emergency Backstop Mechanism.
The new requirements will apply to eligible installations based on when their distribution network connection applications are submitted and approved.
Important changes for Endeavour Energy installations
Effective from 2 November 2026
If you’re completing new or upgraded solar and battery installations within Endeavour Energy’s network, there are important changes to your installation workflow.
For eligible systems where the network connection application is submitted and approved from 2 November 2026, you must use the NSW CER Installer Portal to complete the relevant installation notification, commissioning and CCEW requirements.
What installers need to do
-
Continue submitting network connection applications
Connection applications must still be submitted through Endeavour Energy’s existing connection application process.
-
Register for the NSW CER Installer Portal
Installers need to register using their valid electrical licence details. Solar retailers and applicants must also register so that installations can be assigned to the appropriate installer.
-
Complete installation notifications and CCEWs
For applicable installations, the installation notification and solar installation CCEW are now completed through the NSW CER Installer Portal rather than separately through the existing Building Commission NSW eCert process.
-
Check equipment and connectivity requirements
Ensure equipment meets the applicable technical standards, including Common Smart Inverter Profile – Australia (CSIP-AUS) requirements, and that suitable internet connectivity is available where required.
-
Complete additional testing when applicable
Device Registration Verification and Capability Testing will be introduced progressively by Endeavour Energy, based on the installation location and rollout phase.
Installers should confirm the requirements for their postcode before commencing work.
Important: The requirement to use the CER Installer Portal and the requirement to complete Emergency Backstop capability testing do not necessarily commence on the same date.
What is the Emergency Backstop Mechanism?
The NSW Emergency Backstop Mechanism is designed to help maintain electricity network stability during rare periods when electricity generation exceeds demand.
It enables distribution networks to temporarily reduce solar exports or generation when instructed by the Australian Energy Market Operator (AEMO) as a last-resort measure.
For installers, this means applicable new and upgraded rooftop solar systems will need compatible inverters and the ability to communicate with their electricity distribution network.
Endeavour Energy is progressively introducing these requirements, with the rollout scheduled to reach all new and upgrading solar installations by 1 February 2027.
For applicable Endeavour Energy systems without reliable internet connectivity, a temporary export limit of 1.5 kW may apply until connectivity is established. Installers should refer to Endeavour Energy’s published guidance for applicable exceptions and requirements.
What does this mean for CCEWs?
For eligible solar and battery installations covered by the new portal, the CCEW can be completed as part of the CER Installer Portal workflow.
This means installers will no longer need to separately lodge the CCEW through Building Commission NSW eCert for that same eligible work.
However, if an installation includes additional electrical work that falls outside the scope of the CER Installer Portal, a separate CCEW through Building Commission NSW eCert may still be required.
What does this mean for Formbay users?
Formbay customers completing solar and battery installations in NSW should familiarise themselves with the new requirements and account for the additional steps in their installation and commissioning processes.
The NSW CER Installer Portal is a separate government system, and installers must ensure the applicable network registration and electrical certification requirements are completed through the appropriate channels.
These requirements are separate from renewable energy certificate processing through Formbay.
We encourage customers to review the latest guidance from the NSW Government and their relevant distribution network before commencing new installations.
How to prepare
To ensure you’re ready for the changes:
-
Register for the portal: Set up your NSW CER Installer Portal account and confirm your installer or applicant details.
-
Complete the training: Access the free Clean Energy Council Learn LAB training to understand the new process.
-
Review your installation pipeline: Check which upcoming installations are subject to the new requirements based on their network connection approval dates.
-
Check equipment compatibility: Confirm that your inverters and other applicable equipment meet the network’s technical requirements.
-
Check your network rollout: Review the applicable Emergency Backstop commencement dates for each installation location.
Helpful resources
Official information, eligibility requirements and commencement dates.
https://www.energy.nsw.gov.au/nsw-plans-and-progress/regulation-and-policy/installer-portal NSW CER Installer Portal SupportRegistration guides, instructional videos and technical support information.
https://www.energy.nsw.gov.au/nsw-plans-and-progress/regulation-and-policy/installer-portal/cer-installer-portal-support Endeavour Energy Installer InformationNetwork-specific requirements, Emergency Backstop rollout information and installation guidance.
https://www.endeavourenergy.com.au/working-with-us/providers/solar-retailers-and-installers Access the NSW CER Installer Portal https://installerportal.energy.nsw.gov.au/Questions about NSW installations?
Contact the Formbay support team.